Baseline-systems BaseStation 3200 Manual de usuario Pagina 53
- Pagina / 82
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
C h a p t e r 4 – T r o u b l e s h o o t i n g
Page 51
Baseline 3200
4
Troubleshooting
Section Contents
Zones, Valves and biCoders ................................................................................................51
Soil Moisture biSensors ......................................................................................................51
Two-Wire – High Current or Shorted ..................................................................................52
Lost Devices | No Response ................................................................................................53
Messages | Alerts ...............................................................................................................53
Zones, Valves and biCoders
The following table identifies some common problems and solutions. For all of these types of
problems, start with a zone self-test.
1. Turn dial to Self-test position.
2. Highlight the Test Zone menu and press ENTR.
3. Use the + and – keys to select the zone number.
4. Press ENTR to test the zone (this will activate the valve for less than a second to
measure the voltage and current through the valve solenoid). This test will return the
solenoid current and the
Self-test status
Cause/Action
Open circuit
Wire connection between the valve biCoder and the valve
solenoid is broken – repair wire connections.
Valve solenoid is broken – replace solenoid.
Short circuit
Wire connection between the valve biCoder and the valve
solenoid is shorted together – repair wire connections.
Valve solenoid is broken – replace solenoid.
No response
Two-wire connection to the valve biCoder is broken – repair
wire and connections to the valve biCoder.
Two-wire voltage loss is too high – check other devices in
same vicinity for high two-wire voltage loss – repair high
resistance connections between controller and devices.
Valve biCoder is damaged – remove biCoder and move it
directly to the controller to test its ability to communicate.
Soil Moisture biSensors
The following table identifies some common problems and solutions. For all of these types of
problems, start with a biSensor self-test.
1. Turn dial to Self-test position.
2. Highlight the Test biSensor menu and press ENTR.
3. Use the + and – keys to select the biSensor number.
- Advanced Irrigation 1
- Controller 1
- Table of Contents 4
- Baseline 3200 5
- Introduction 7
- Cabinet Options 8
- How to Irrigate Efficiently 9
- Soil Moisture Content 10
- Watering Strategies 11
- Zone Schedule Groups 12
- Soak Cycling 13
- Distribution Uniformity 14
- I n t r o d u c t i o n 15
- C-series Wall Mount Cabinets 16
- Getting Started 16
- P-series Pedestals Cabinets 18
- Wireless Rain Sensors 20
- Conventional Wiring Modules 20
- Expanding with Two-wire 21
- Two-wire Installation 22
- Two-wire Serial Numbers 22
- Wire Type 23
- Wire Connections 23
- Wire Lengths 24
- Wire Layout 24
- Field Decoder Wiring 25
- Surge Protection 25
- Example Wiring Diagram 26
- Maximum Concurrent Valves 27
- Choosing the Sensor Location 28
- Burying the biSensor 29
- Turfgrass 30
- Trees and Shrubs 30
- Gardens and Crop Plants 31
- Step 1: Search for biCoders 33
- Assigning Other Devices 34
- Auto Run Main Screen 35
- BL Commander Mobile Receiver 36
- Basic Programming 37
- Time Based Watering 37
- Each of the zone values 37
- Using Soak-Cycles 38
- Programs 38
- Water Windows 39
- Day Intervals 39
- Historical ET Based Watering 40
- Historical ET Calendar 40
- Soil Moisture Based Watering 40
- Micro-Climates and Zone 41
- Scheduling Groups 41
- Make sure to assign the 41
- New grass should not be 41
- Upper Limit 43
- Advanced Programming 45
- Flow Devices 45
- Design Flow 46
- Mainline Limits 47
- Managing Zone Concurrency 48
- Learning Flow 49
- Zone Flow 50
- Pause biCoders 51
- Page 50 52
- Troubleshooting 53
- Zones, Valves and biCoders 53
- Soil Moisture biSensors 53
- Lost devices 55
- Messages 55
- Page 54 56
- Reference 57
- Dial Positions 57
- Auto/Run 57
- Zone Water Times 61
- Start Times 62
- Soak Cycle 64
- MV/Pump Start 64
- Date/Time 65
- Event Days 65
- Flow Menu 66
- To remove a two-wire 68
- AUX – USB Data 69
- AUX – Clear All 69
- AUX – Valves 69
- Changing the controller 70
- Self-Test 70
- Self-Test – Zone Test 71
- Self-Test – Test biSensor 71
- Self-Test – Test All 71
- Manual Run Program 72
- Manual Water 73
- Two-wire Devices 75
- Air Temperature Sensor 75
- Pause biCoder 76
- Valve biCoders 77
- BaseManager 78
- BL-Commander 79
- Warranty 79
- Glossary of Terms 80
Relacionado con productos y manuales para Sensores Baseline-systems BaseStation 3200
(122 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.147 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales