Baseline-systems BaseStation 3200 Manual de usuario Pagina 54
- Pagina / 82
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
C h a p t e r 4 – T r o u b l e s h o o t i n g
Page 52
Baseline 3200
4. Press ENTR to test the biSensor. This test will return the current moisture, soil
temperature, and two-wire voltage drop.
Self-test status
Cause/Action
No response
Two-wire connection to the biSensor is broken – repair wire
and connections to the biSensor.
Two-wire voltage loss is too high – check other devices in
same vicinity for high two-wire voltage loss – repair high
resistance connections between controller and devices.
The biSensor is damaged – remove biSensor and move it
directly to the controller to test its ability to communicate.
Zero Reading
The biSensor detection blade is damaged – if the soil
temperature reading is valid replace the biSensor.
There are additional categories of biSensor conditions that are a result of biSensor placement or
programming that are covered in the following table. These conditions are only valid where the
biSensor is buried.
Condition
Causes/Action
Ground is too dry
with low biSensor
moisture reading
Not enough zone water time – increase water time to apply
at least 0.5” of water
biSensor not being watered by its primary zone – change
assignment or move biSensor to correct location
Program start times are too infrequent – increase the
program start time frequency
biSensor limit is too low – raise limit or run a biSensor
calibration cycle (refer to page 38)
Ground is too dry
with high biSensor
moisture reading
biSensor not being watered by its primary zone – change
assignment or move biSensor to correct location
biSensor is buried too deep – rebury biSensor to be only 3”
deep
Ground is too wet
with high biSensor
moisture reading
biSensor is buried in low area where water collects – move
biSensor from low area
biSensor not being watered by its primary zone – change
assignment or move biSensor to correct location
Program start times are too often – increase the interval
between start times
biSensor limit is too high – lower limit or run a biSensor
calibration cycle (refer to page 38)
Ground is too wet
with low biSensor
moisture reading
biSensor not being watered by its primary zone – change
assignment or move biSensor to correct location
biSensor is buried too deep – rebury biSensor to be only 3”
deep
Not enough zone water time – increase water time to apply
at least 0.5” of water
- Advanced Irrigation 1
- Controller 1
- Table of Contents 4
- Baseline 3200 5
- Introduction 7
- Cabinet Options 8
- How to Irrigate Efficiently 9
- Soil Moisture Content 10
- Watering Strategies 11
- Zone Schedule Groups 12
- Soak Cycling 13
- Distribution Uniformity 14
- I n t r o d u c t i o n 15
- C-series Wall Mount Cabinets 16
- Getting Started 16
- P-series Pedestals Cabinets 18
- Wireless Rain Sensors 20
- Conventional Wiring Modules 20
- Expanding with Two-wire 21
- Two-wire Installation 22
- Two-wire Serial Numbers 22
- Wire Type 23
- Wire Connections 23
- Wire Lengths 24
- Wire Layout 24
- Field Decoder Wiring 25
- Surge Protection 25
- Example Wiring Diagram 26
- Maximum Concurrent Valves 27
- Choosing the Sensor Location 28
- Burying the biSensor 29
- Turfgrass 30
- Trees and Shrubs 30
- Gardens and Crop Plants 31
- Step 1: Search for biCoders 33
- Assigning Other Devices 34
- Auto Run Main Screen 35
- BL Commander Mobile Receiver 36
- Basic Programming 37
- Time Based Watering 37
- Each of the zone values 37
- Using Soak-Cycles 38
- Programs 38
- Water Windows 39
- Day Intervals 39
- Historical ET Based Watering 40
- Historical ET Calendar 40
- Soil Moisture Based Watering 40
- Micro-Climates and Zone 41
- Scheduling Groups 41
- Make sure to assign the 41
- New grass should not be 41
- Upper Limit 43
- Advanced Programming 45
- Flow Devices 45
- Design Flow 46
- Mainline Limits 47
- Managing Zone Concurrency 48
- Learning Flow 49
- Zone Flow 50
- Pause biCoders 51
- Page 50 52
- Troubleshooting 53
- Zones, Valves and biCoders 53
- Soil Moisture biSensors 53
- Lost devices 55
- Messages 55
- Page 54 56
- Reference 57
- Dial Positions 57
- Auto/Run 57
- Zone Water Times 61
- Start Times 62
- Soak Cycle 64
- MV/Pump Start 64
- Date/Time 65
- Event Days 65
- Flow Menu 66
- To remove a two-wire 68
- AUX – USB Data 69
- AUX – Clear All 69
- AUX – Valves 69
- Changing the controller 70
- Self-Test 70
- Self-Test – Zone Test 71
- Self-Test – Test biSensor 71
- Self-Test – Test All 71
- Manual Run Program 72
- Manual Water 73
- Two-wire Devices 75
- Air Temperature Sensor 75
- Pause biCoder 76
- Valve biCoders 77
- BaseManager 78
- BL-Commander 79
- Warranty 79
- Glossary of Terms 80
Relacionado con productos y manuales para Sensores Baseline-systems BaseStation 3200
(122 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.106 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales